High-speed cylinder printer hardware system description

Table Of Contents

PH headboard interface description

PH headboard (standard configuration 3H)

Front panel interface description (standard configuration 3H)

No.Coordinate No.NameDescription
1J1-J61-way – 6-way ink cartridge liquid levelUsed as the secondary ink cartridge liquid level switch signal interface (WKCMYV)
2J7-J87-way to 8-way ink cartridge liquid levelspare interface
3J9Waste ink level protectionWST is the signal interface of the waste ink bottle (air bottle) liquid level switch, two safety bottles are connected in series
No.Coordinate No.NameDescription
4J11Upper limitThe sensor signal interface of the upper limit of the headstock (Z-axis origin)
4J12Lower limitThe sensor signal interface for the lower limit of the headstock (Z-axis endpoint).
5J13Anti-collision sensorThe signal interface of the front anti-collision sensor, the connection method of more than two safety bottles is a series connection
6J14Height measuring sensorIgnore if there is no height-measuring device
7J15Z axis motor 
8J20Height measuring probe (electromagnet)Ignore it if there is no height-measuring device
9U9Optical fiberIf the insertion sequence of AB is correct, when the power is turned on, the patch next to the optical fiber interface of the main board The LED “D2” indicator light will always be on, if it is inserted backward, D2 will not be on
10J20Power supply37V and 24V
12PH1(J1,J4)White ink print headJ1 corresponds to the upper slot of the print head, J4 corresponds to the lower slot of the print head
13PH2(J2,J5)Color ink print headJ2 corresponds to the upper slot of the print head, J5 corresponds to the lower slot of the print head
14PH3(J3,J6)Varnish headJ3 corresponds to the upper slot of the nozzle, J6 corresponds to the lower slot of the nozzle
15J24,J25,J26Head heatingJust connect any two of them

GE motherboard interface description (standard configuration)

GE Mainboard (Standard Configuration 3H)

GE motherboard interface description (standard configuration 3H)

No.Coordinate No.NameDescription
1J24Rotary motorMOTOR1 is the drive signal interface of the Y rotary motor.
2J25Stepper motorMOTOR2 is the interface for X stepper motor drive signal
3J22Rotation internal originRotation motor internal origin. Phase A of this interface is used as the frequency division output interface of phase Z of the rotary motor encoder. The pin numbers of the interface A+ and A- correspond to the CN1 terminal of the servo are 27 (Z+) and 28 (Z-)
4J23X FeedbackRotary motor encoder feedback. It is the A and B phase frequency division output interface of the rotary motor encoder, corresponding to the servo tubeThe foot numbers are 23 (A+) and 24 (A-), 25 (B+), and 26 (B-)
5J18Power24V power interface
6J20Short circuitShort circuit G (GND) and S (SIGNAL), V (+VCC) not connected
7J16Left limitLeft limit interface, if there is no left limit, short G (GND) and S (SIGNAL), V (+VCC) not connected
8J17Right originIt is the origin (right limit) sensor signal interface of the stepper motor, the sensor is connected to the normally closed end, and connected to the G(GND), S(SIGNAL signal), and V(+VCC)
11J11One-key printingOne-key printing button signal, connected to G (GND) and S (SIGNAL), not connected to V (+VCC)
13J5UV lamp (main lamp)It is the control signal interface of the main UV lamp, and the positive and negative poles are wired according to the silk screen +- marks on the board
14J4UV lamp (varnish)It is the control signal interface of the varnish UV lamp (if there is no varnish lamp, it can be ignored), the positive and negative poles are printed on the board +-Label wiring
15J3OutputPin 10 is the stirring motor signal (positive pole), pin 12 is the signal of printing completion (positive pole), G(GND)
16J2Ink supply pumpIt is the ink pump interface, 5 channels are used for (Y), 6 channels are used for (V), 7 channels (spare), 8 channels (spare)
17J1Ink supply pumpIt is the ink pump interface, 1 way is used as (W), 2 way is used as (K), 3 way is used as (C), 4 way is used as (M)
18J18Gigabit Ethernet portOne end of the network cable is connected to this port, and the other end is connected to the network port of the computer
20J32RS485 B485 protocol UV lamp segmentation control signal
21J31RS485 ARS485 communication line interface signal of servo driver CN4/5, terminal pins 1, 2, and 7 correspond to connect A, B, and G
22U10Optical fiberPort with ▲ the symbol engraved on it means receiving (corresponding to headboard sending ▼), engraved with ▼ a symbol on it means sending (corresponding to Headboard receiving ▲)
small_c_popup.png

Let's have a chat

Learn how we helped 100 top brands gain success.